Porter cable 7800 instruction manual

Page 7: Functional Description The Sander provides a superior finish, and is faster than conventional finishing methods for both new construction and renovation work. Clean-up time for Model is minimized by the use of an external vacuum cleaner attached to the sander. Lay the cord and the vacuum hose out parallel to each other. Place a strap approximately two feet from each end and place the third strap halfway between the other two. The speed is adjusted by turning the control knob B Fig.

Model only. Page 11 Use a steady, sweeping motion. Stopping the Sander on the work, or moving the Sander erratically can cause unacceptable swirl marks and unevenness in the work surface. Page Transportation And Storage Fig. Do not allow anything to press against the abrasive pad.

The pad might deform, causing it to sand unevenly. If the pad cannot be protected during transport or storage: remove the abrasive pad and store it separately. Page Service And Repairs In any communications, please give all information shown on the nameplate of your tool model number, type, serial number, etc.

We will repair or replace, at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period.

This manual is also suitable for: Print page 1 Print document 16 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Pull the lever B and set the router on the workpiece. With the router flat and level, let the bit barely touch the workpiece.

Hold the lever B and turn the depth knob C until the zero aligns with the zero mark on the router base. Release the lever B. Make sure that the zero remains aligned with the zero mark. Turn the knob C clockwise to the desired depth of cut. To connect the router to a vacuum cleaner for dust extraction, follow these steps:. Remove the dust cap E Fig. Insert the dust extraction hose adapter F into the dust extraction port G as shown.

Insert the end of a standard vacuum cleaner tube H into the hose adapter. When using dust extraction, be aware of the placement of the vacuum cleaner.

Be sure that the vacuum cleaner is stable and that its hose will not interfere with the work. An accidental startup can cause injury.

Loosen the depth rod locking knob J Fig. Normally the deepest desired cut is set with the depth rod resting on the lowest point on the turret dial N Fig. Push the router down until the bit touches the work surface.

Push the locking lever O down to lock the router in this position. Tighten the depth-rod locking knob J Fig. Position the depth indicator P Fig. Loosen the depth-rod locking knob J Fig. Before starting the tool, clear the work area of all foreign objects. Keep a firm grip on the tool to resist starting torque. Two switches A and B Fig. This router is equipped with a variable speed control A Fig.

In low and medium speed operation, the speed control prevents the motor speed from decreasing. If you expect to hear a speed change and continue to load the motor, you could damage the motor by overheating.

Always be sure the work is rigidly clamped or otherwise secured before making a cut. Since the cutter rotates clockwise when viewing router from top , move the router from left to right as you stand facing the work. When working on the inside of a templet, move the router in a clockwise direction. When working on the outside of a templet, move the router in a counterclockwise direction.

Make smaller cuts and remove minimal material with each pass. Remove the handle from the router base. Store the handle and screw for possible later use. Remove the plastic plug from the dust port B Fig. Remove the screws B Fig. Insert a hex screw G Fig. From inside the base housing, place a shoulder washer H and a hex nut J on the screw.

Tighten the nut loosely. Turn the router base upside down and place the dust deflector E Figs. Align the extended part of the deflector B Fig. The deflector will be flush with bottom of router base. Replace the sub-base and the three screws Fig.

Tighten all hardware securely. A wide variety of template guides is available for use in pattern and templet routing operations. To install, insert the templet guide in the center hole of the router base and secure it in place with a locknut. See Fig. Before connecting the router to the power source, install the bit, adjust the depth of cut, and rotate the router chuck by hand to ensure that the bit or collet do not contact the templet guide.

The router can be mounted to a router accessory table not included. To open the clamp for motor removal, use a hex wrench in the hole C , Fig.

To adjust cutting depth, use a hex wtrench in the hole D Fig. For instructions on how to mount the router to the router accessory table, refer to the accessory table instruction manual. For assistance with your tool, visit our website at www. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool.

Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line. No further lubrication is necessary. At approximately hours of use, take or send your tool to your nearest Porter-Cable Factory Service center or Porter-Cable Authorized Warranty Service Center to be thoroughly cleaned and inspected. Have worn parts replaced and lubricated with fresh lubricant. Have new brushes installed, and test the tool for performance.

Any loss of power before the above maintenance check may indicate the need for immediate servicing of your tool. If proper operating voltage is present, return your tool to the service station for immediate service.

Use only identical replacement parts. For a parts list or to order parts, visit our website at servicenet. Or, you can call our Customer Care Center at For information about Por- ter-Cable, its factory service centers or authorized warranty service centers, visit our website at www. All repairs made by our service centers are fully guaranteed against defective material and workmanship.

We cannot guarantee repairs made or attempted by others. Be sure to include all of the information shown on the nameplate of your tool model number, type, serial number, etc. Please visit our Web Site www. Since accessories other than those offered by Porter-Cable have not been tested with this product, use of such accessories could be hazardous.

For safest operation, only Porter-Cable recommended accessories should be used with this product. To register your tool for warranty service visit our website at www. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period.

Proof of purchase may be required. This warranty does not apply to repair or replacement required due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our servicecCenters or authorized warranty service centers.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. If your warning labels become illegible or are missing, call for a free replacement. Lire toutes les directives. En cas de doute, utiliser le calibre suivant le plus gros. Toujours porter une protection oculaire. Welcome to ManualMachine. We have sent a verification link to to complete your registration.

Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. A Instructivo de operacion, centros de servicio y poliza de garantia. General Safety Rules Read all instructions. The symbols and their definitions are as follows: V OPERATION To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs.

To remove the motor unit from the base unit: a Open the clamp A Fig. Lower the Fig. Pull the lever I Fig. Remove the power unit from the base. The sub-base for the fixed base model can be replaced with an accessory sub-base that is 3. Clean and insert the shank of the bit into the collet until the shank bottoms, then back it out suitable for use with template guides. To do this: 4.

To reduce the risk of injury, turn unit off and disconnect it from power source before 5. An accidental start- 6. To reduce the risk of injury, turn unit off and disconnect it from power source before 2. Close the clamp A. To connect the router to a vacuum cleaner for dust extraction, follow these steps: 1.

Adjust the speed by turning the speed control knob A. Router base B. Dust port C. GripVac handle D. Removed handle and screw E.

Dust deflector F. Sub-base with screws G. Hex screw 2 H.