Karcher service manual

Danger of chemical burns. Filling water in while the battery is discharged can lead to acid leaks! Wear goggles when handling battery acid and adhere to instructions to prevent injuries and damage to clothing.

Flush any acid drops on the skin or clothes immediately with plenty of water. Use only distilled or desalinated water EN T3 for filling the battery. Do not add any substances so-called performance improving agents , else warranty claims will not be entertained. With the initial charge, the control will not yet be able to detect which battery type has been installed.

Keep charging the batteries until the display shows a full charge batteries may still not be completely charged. The next charging process will have an accurate display and charge power and the batteries will be fully charged. A "V" to the right of the bar of the battery indicator shows that the initial charge has not been performed yet.

Use the appliance until the deep discharge protection switches off the brush motor and the turbine after the initial charge of the battery. This procedure is necessary to adjust the battery indicator. Only then the correct battery status is displayed. To take all functions out of operation immediately, bring the safety switch into the "0" position. Unscrew these boards. Place the boards in such a way that they lie in front of the four wheels of the machine. Fasten the boards with screws.

The procedure for changing the cleaning head is described in the chapter "Maintenance Tasks". The installation of the brushes is described in the chapter "Maintenance Tasks".

Risk of injuries. Never use the unit without protective roof in areas where the operators can be hit by dropping objects. Risk of accident. Prior to every operation, the parking brake must be checked for proper function on a level ground.

The machine must roll easily on a plane surface. When the pedal is released, the brake locks audibly. Switch off the machine and call the aftersales service if the above-men- tioned events do not occur. Danger of tipping on unstable ground. The drive direction can also be changed during the drive. Thus, very blunt edges can be polished by moving forward and backward a few times.

In case of overloading, the drive motor automatically switches off after a certain period. A fault message is displayed on the console. The concerned unit gets switched off if the controls get overheated.

Risk of damage. Only use the recommended detergents. With respect to different detergents the operator bears the increased risk regarding the operational safety and danger of accident. Only use detergents that are free from solvents, hydrochloric acid and hydrofluoric acid. If detergent is added to the cleaning detergent tank first, followed by water, there could be a lot of foam. Fill up the fresh water tank completely before starting up the machine to ventilate the water supply system.

Once the maximum fill level is reached, the built-in floater valve will stop the water inflow. Depending on the authorisation of the yellow Intelligent Key, individual parameters can be changed.

The modification of the parameters is only valid until another cleaning programme is selected via the programme selection switch. If you wish to permanently change the parameters, you must use a grey Intelligent Key. Almost all displayed text regarding parameter adjustment is self-explanato- ry. The only exception is the parameter FACT:. If the vacuum result is unsatisfactory the inclination of the straight vacuum bar can be modified.

The hose with the spray nozzle is attached to the back of the appliance. It serves for washing away dirt and for manual cleaning of the wastewater tank. Overflow wastewater tank. When the wastewater tank is full, the suction turbine switches off and "Wastewater tank full" is shown on the display. If needed, remove and empty waste container after work.

In this menu item the authorisations for yellow intelligent keys as well as the language of the display texts are selected. Changes of the parameters of the individual cleaning programmes that were made during the operation are reset to the basic setting after switching off the appliance. Parameters that are adjusted with the grey Intelligent Key, are kept until another setting is selected. Risk of injury! When loading or unloading the appliance, it may only be operated on gradients of max.

Drive slowly. Risk of injury and damage! Observe the weight of the appliance when you transport it. Note the weight of the appliance in case of storage. Before working on the appliance, remove the Intelligent Key and the mains plug of the charger. Suction turbine will continue to run for a while after switch-off. Carry out maintenance tasks only after the suction turbine has come to a halt. Do not sluice the appliance with water and do not use aggressive detergents.

Ensure that the connection cable sits firmly. The subsequent removal will take place in the opposite order of the installation. In case of faults that cannot be remedied using the table below please contact the customer service. Only carry out the troubleshooting measures in the indicated order if the error occurs again. The key switch must be in the "0" position and the emergency stop button pressed. Error messages that are not listed in the following table, point to errors that cannot be fixed by the operator.

If these are displayed, consult Customer Service. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. B R. NOTICE: This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard s Operation is subject to the following two conditions: 1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.

Do not use any type of adapter with this product. The training shall inform the trainee that: A The primary responsibility of the operator is to use the powered floor.

A Fundamentals of the powered floor scrubber s the trainee will operate: 1 characteristics of the powered floor scrubber s , including variations between powered floor scrubbers in the workplace; 2 similarities to and differences from automobiles; 3 significance of nameplate data, warnings, and instructions affixed to the powered floor scrubber; 4 operating instructions and warnings in the operating manual for the powered floor scrubber, and instructions for inspection and maintenance to be performed by the operator; 5 type of motive power and its characteristics; 6 method of steering; 7 braking method and characteristics; 8 visibility forward and reverse; 9 stability characteristics with and without load, with and without attachments; 10 controls-location, function, method of operation, identification of symbols; 11 battery charging; 12 guards and protective devices for the specific type of powered floor scrubber; 13 other caracteristics of the specific powered floor scrubber.

B Operating enviroment and its effect on powered floor scrubber operation, including: 1 floor or ground conditons including temporary conditions; 2 ramps and inclines; 3 battery charging facilities; 4 narrow aisles, doorways, overhead wires and piping, and other areas of limited clearance; 5 areas where the powered floor scrubber may be operated near other powered industrial trucks, other vehicles, or pedestrians; 6 use and capacity of elevators;.

C Operation of the powered floor scrubber, including: 1 proper preshift inspection and approved method for removing from service a powered floor scrubber which is in need or repair; 2 travelling, turning corners; 3 parking and shutdown procedures; 4 other special operating conditions for the specific application. E Operational training practice, including: 1 if feasible, practice in the operation of powered floor scrubbers shall be conducted in an area separate from other workplace activities and personnel; 2 training practice shall be conducted under the supervision of the trainer; 3 training practice shall include the actual operation or simulated performance of all operating tasks such maneuvereing, travelling, stopping, starting, and other activities under the conditions which will be encountered in the use of the powered floor scrubber.

General Before starting to operate the powered floor scrubber: A be in operating position; B place directional controls in neutral; C apply brake; D turn switch to ON position. Do not add to, or modify the unit. Do not block access to fire aisles, stairways or fire equipment. Travelling Observe all traffic regulations including authorized plant speed limits. Do not pass another truck travelling in the same direction at intersections,. Do not indulge in stunt driving or horseplay.

The operation of a powered floor scrubber requires special safety considerations, as follows: A A powered floor scrubber may tip over if an operator fails to slow down to a safe speed before making turns.

Indications that a truck is being driven at an excessive speed during turning maneuvers include: 1 tire skidding; 2 unit side sway; 3 wheel lift; and. B The likelihood of lateral tipover is increased under any of the following conditions, or combinations of them: 1 travelling on an uneven surface; 2 travelling at excessive speed.

C Tipping forward can occur and its likeliehood is increased under the following conditions, or combination of them: 1 The operator should stay with the powered floor scrubber if it falls off a loading dock or ramp. Before starting inspection and repair of powered floor scrubber: A raise drive wheels free of floor and disconnect battery and use chocks or other positive truck-posirioning devices; B block chassis before working on them; C disconnect battery before working in the electrical system; D the charger connector shall be plugged only into the battery connector and never into the unit connector.

A Before starting to operate the unit: 1 be in operating position; 2 apply brake; 3 place directional controls in neutral; 4 turn switch to ON position; 5 check functioning of lift and tilt systems, steering, warning devices, and brakes.

B Before leaving the unit: 1 stop unit;. Properly ventilate work area, vent exhaust fumes, and keep shop clean and dry. Changing and Charging Storage Batteries. Facilities shall be provided for the following: A Flushing spilled electrolyte; B Fire protection; C Protecting charging apparatus from damage by trucks, and D Adequate ventilation for dispersal of fumes from gasing batteries.

The powered floor scrubber shall be positioned properly and brakes shall be applied before attempting to change or charge batteries. Smoking shall be prohibited in the charging area. The unit shall not be used in classified areas. Please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent owners.

Contents Safety instructions. Safety Devices Safety devices serve to protect the user and must not be rendered in operational or their functions bypassed. Safety button To take all functions out of operation immediately: Bring the safety switch into the "0" position.

Seat switch Switches off the drive motor after a short delay, if the operator leaves the operator seat during operation or while moving. Keep hands away from this area while swivelling down the waste water tank.

Drive slowly on slopes. Function The scrubber vacuum is used for wet cleaning or polishing of level floors. Proper use Use this appliance only as directed in these operating instructions. Details of load per surface unit can be found in the technical data. Environmental protection The packaging materials are recyclable. Wet clean the floor and allow the detergent to react. Before Startup Batteries Observe the directions on the battery, in the instructions for use and in the vehicle operating instructions Wear eye protection Keep children away from acid and batteries Danger of explosion Fire, sparks, naked flames and smoking must be strictly avoided Danger of chemical burns First aid Warning note Disposal Do not throw the battery into the regular waste DANGER Risk of explosion!

Recommended batteries Order No. Ensure correct polarity. Part numbers. Sizing Software. Hydraulic Motors. Quick Couplings. High Pressure Spiral Hose. ParkerStore has a solution for your hydraulic or pneumatic applications. The combination of high temperature and high pressure may reduce hose life. Coupleur femelle KW pour pistolet avec sortie M22 M. KW : M22 M. Pour lances avec raccord manuel. Coupleur KW : M22 F. Ici logo du client However, a sod production operation newly established in Tennessee will not be without competition.

Using a foot hose, the time required to apply 1 inch of water per pull would be minutes For the proof of the last inequality we use. June Hargis Industries, Inc. Kits de joints haute-pression HD S Manual Grease Pump Operating pressure Bar. Susan Karcher is a faculty member of the Department of Biological Sciences at Before the laboratory time for this experiment, students do the Independent Project.

Plan provided below that asks them basic questions about the system and asks them to plan Annual review of Microbiology All Rights Reserved. Designed by Templatic. Home Copyright Privacy Contact. Additionally, you need a service provider that leaves no stone unturned: with fast, reliable operational service on-site; with all of the necessary tools, spare parts and wear parts; and with ideally tailored packages for inspection, servicing and full service.

That's our promise! He prides himself on developing relationships with his customers, based on trust and respect. Learn more about his story by watching this short video. We appreciate your business and strive to deliver the best experience while meeting your service needs. Karcher has a central dispatch center that handles all service request nationwide.

You can find the material and serial number on our service sticker or type plate. These are affixed to the machine in a clearly visible location. You can find the machine designation on the machine itself or on the type plate. Depending on the unit type, you will find the type plate on the rear, underside or inside the machine.

Utilize one of our many packages and your equipment's life will not only be extended, but it will also reduce your downtime costs. Regardless of the brand of machines in your fleet, we can support you with competent, reliable and fast service. Skip to content Skip to navigation. Equipment Service. You manage your business. We give you security. Repairs on site In the event of any repair work, you will receive first-class, quick and effective service from us.

The Repairs Procedure: Need a repair? No problem. Simply contact us by phone, through our Service app , by fax or e-mail. We'll keep you updated Shortly after accepting the order, you will receive an order confirmation through the Service app, by e-mail or fax.

Quick appointment arrangement We'll arrange an appointment with you. Thanks to our efficient route planning system, we'll be with you as quickly as possible.